[Gelöst] Patch 1.1.0

  system environment

• Windows 25H2
• Bitwig 6 Beta V15
• VST 3
• Reecer-Version 1.1.0

Error description

Preset browser/ save preset

• Not a bug as such but it would be nice if the dialogue could remember that last username when saving a patch, so you don’t have to type that in every time

Play Mode:

• Legato does not appear to work

Filter ADSR:

• I had made a default patch which I have now deleted (deleted the previous testing patches so back to 0 Presets) reloaded Reecer the FLT ADSR Mix defaults to 100% (F1 ENV 0% & F2 ENV 0%)

It’s hard to tell exactly what’s going on: Set up Single OCS Filter ADSR Mix 100%, F1 ENV 100%, Atk 0%, Dec 5.0ms, Rel 0.00, LP 24db, Res 30%

Pattern 3 x 1/16^th notes (slightly shorter to allow for 15ms release with no overlap) 100bpm

• F1 Cut 10HZ (visual feedback on the knob would suggest around 50% bipolar motion however in reality it looks like the filter peaks at around 16hz
• ADRS feedback suggests bipolar I think a standard unipolar envelope would work better
• To hit full frequency within the filter sweep min value of the filter can only go to 4834hz which doesn’t then sweep low enough to make a Psy bass

I am Aware 1/16 at 100BPM is 150ms with decay set to 100ms (Sus still 0)

• F1 cut at 10HZ (visual feedback on the knob is inconsistent varying between 15% & 50%) there is no difference in the filter response with F1 env at 100 and F1 env at 0
• Min F1 Cut to get full frequency with 100ms dec, Sus 0% is around 10000Hz which doesn’t sweep low enough for a Psy bass

LFO:

• Retrigger on LFO 1,2 &3 does not appear to be working, tried sync on and off does not retrigger with midi or play back
• Clicking the white header above GUI cause LFO motion to pause on all LFO’s

Modulation Matrix:

• FM Amt A does not appear to work (not sure if this is a legit target as there is no FM Amt A in the FM section)
• FM Amt B does not appear to work
• Pitch A does not appear to work
• Pitch B does not appear to work
• Pan A does not appear to work
• Pan B does not appear to work
• FLT mix does not appear to work
• Drive (under FLT mix) if that is FLT drive does not appear to work (although not sure that is a legit target as there is nod drive parameter in the filter
• LFO 1 rate does not appear to work
• LFO 2 rate does not appear to work
• LFO 3 rate does not appear to work
• Macro 1-4 Works no visual feedback on the knobs though
• Sub Level does not appear to work
• OSC A level does not appear to work
• OSC B level does not appear to work
• Phase offset does not appear to work
• Formant A does not appear to work
• DRV1 Amt does not appear to work
• DRV1 Mix does not appear to work
• Chorus all 3 parameters have no visual feedback but do not appear to work

Filters:

• Bell Filter behaves the same as the band pass filter
• Low shelf behaves like the LP filter
• High Shelf behaves like the HP filter
• Don’t know much about the filter but the ladder filter reduces in volume massively when the Res is pushed to max
• Steiner filter produces side information not sure if that is meant to be the case
• OB SEM start doing weird stuff past 150hz
• Prophet filter produces side information not sure if that is meant to be the case
• Vowel filter produces side information past 219hz not sure if that is meant to be the case
• Karlsen Filter has the same volume behaviour as the ladder filter

Settings Tab:

Something Bugs out the phase restart (not sure what after I was testing the mod targets and the filters the phase start is random and the knob no longer has any effect, resolve when loading a new patch

Thats all i had time for today, defo a lot of improvemnets still a lot to do, thanks for the shout out no problem with with the direct mention (not required though you have been doing a lot for the comunity, I just thought it would be nice to give something back) 

Additionally helpful

• RME baby face Pro FS buffer 1024